In this topic, we give you an overview of the NIC Team properties such as teaming and load balancing modes. We also give you details about the Standby adapter setting and the Primary team interface property. If you have at least two network adapters in a NIC Team, you do not need to designate a Standby adapter for fault tolerance.
-->
Microsoft Nic Teaming SettingsTeaming modes
The options for Teaming mode are Switch Independent and Switch Dependent. The Switch Dependent mode includes Static Teaming and Link Aggregation Control Protocol (LACP).
Jun 12, 2019 Is there an ETA on when this 'HOT FIX' is going to be released? Some post mentioned it will be earlier February 2017, could you confirm that? From NIC Teaming failed (Build 10568) Windows 10 'There are no native LBFO capabilities on Win10. Microsoft does not support client SKU network teaming. It was a defect in Windows 10 build 10240 that “New.
Tip
For best NIC Team performance, we recommend that you use a Load Balancing mode of Dynamic distribution.
Switch Independent
With Switch Independent mode, the switch or switches to which the NIC Team members are connected are unaware of the presence of the NIC team and do not determine how to distribute network traffic to NIC Team members - instead, the NIC Team distributes inbound network traffic across the NIC Team members.
When you use Switch Independent mode with Dynamic distribution, the network traffic load is distributed based on the TCP Ports address hash as modified by the Dynamic load balancing algorithm. The Dynamic load balancing algorithm redistributes flows to optimize team member bandwidth utilization so that individual flow transmissions can move from one active team member to another. The algorithm takes into account the small possibility that redistributing traffic could cause out-of-order delivery of packets, so it takes steps to minimize that possibility.
Switch Dependent
With Switch Dependent modes, the switch to which the NIC Team members are connected determines how to distribute the inbound network traffic among the NIC Team members. The switch has complete independence to determine how to distribute the network traffic across the NIC Team members.
Important
Switch dependent teaming requires that all team members are connected to the same physical switch or a multi-chassis switch that shares a switch ID among the multiple chassis.
When you use Switch Dependent modes with Dynamic distribution, the network traffic load is distributed based on the TransportPorts address hash as modified by the Dynamic load balancing algorithm. The Dynamic load balancing algorithm redistributes flows to optimize team member bandwidth utilization. Individual flow transmissions can move from one active team member to another as part of the dynamic distribution. The algorithm takes into account the small possibility that redistributing traffic could cause out-of-order delivery of packets, so it takes steps to minimize that possibility.
As with all switch dependent configurations, the switch determines how to distribute the inbound traffic among the team members. The switch is expected to do a reasonable job of distributing the traffic across the team members but it has complete independence to determine how it does so.
Load Balancing modes
The options for Load Balancing distribution mode are Address Hash, Hyper-V Port, and Dynamic.
Microsoft Nic Teaming Jumbo FramesAddress Hash
With Address Hash, this mode creates a hash based on address components of the packet, which then get assigned to one of the available adapters. Usually, this mechanism alone is sufficient to create a reasonable balance across the available adapters.
Use Windows PowerShell to specify values for the following hashing function components.
The TCP ports hash creates the most granular distribution of traffic streams, resulting in smaller streams that can be independently moved between NIC team members. However, you cannot use the TCP ports hash for traffic that is not TCP or UDP-based, or where the TCP and UDP ports are hidden from the stack, such as with IPsec-protected traffic. In these cases, the hash automatically uses the IP address hash or, if the traffic is not IP traffic, the MAC address hash is used.
Hyper-V Port
With Hyper-V Port, NIC Teams configured on Hyper-V hosts give VMs independent MAC addresses. The VMs MAC address or the VM ported connected to the Hyper-V switch, can be used to divide network traffic between NIC Team members. You cannot configure NIC Teams that you create within VMs with the Hyper-V Port load balancing mode. Instead, use the Address Hash mode.
Microsoft Nic Teaming Switch Independent
Because the adjacent switch always sees a particular MAC address on one port, the switch distributes the ingress load (the traffic from the switch to the host) on multiple links based on the destination MAC (VM MAC) address. This is particularly useful when Virtual Machine Queues (VMQs) are used, because a queue can be placed on the specific NIC where the traffic is expected to arrive.
However, if the host has only a few VMs, this mode might not be granular enough to achieve a well-balanced distribution. This mode will also always limit a single VM (i.e., the traffic from a single switch port) to the bandwidth that is available on a single interface. NIC Teaming uses the Hyper-V Virtual Switch Port as the identifier instead of using the source MAC address because, in some instances, a VM might be configured with more than one MAC address on a switch port.
Dynamic
With Dynamic, outbound loads are distributed based on a hash of the TCP ports and IP addresses. Dynamic mode also rebalances loads in real time so that a given outbound flow may move back and forth between team members. Inbound loads, on the other hand, get distributed the same way as Hyper-V Port. In a nutshell, Dynamic mode utilizes the best aspects of both Address Hash and Hyper-V Port and is the highest performing load balancing mode.
The outbound loads in this mode are dynamically balanced based on the concept of flowlets. Just as human speech has natural breaks at the ends of words and sentences, TCP flows (TCP communication streams) also have naturally occurring breaks. The portion of a TCP flow between two such breaks is referred to as a flowlet.
When the dynamic mode algorithm detects that a flowlet boundary has been encountered - such as when a break of sufficient length has occurred in the TCP flow - the algorithm automatically rebalances the flow to another team member if appropriate. In some circumstances the algorithm might also periodically rebalance flows that do not contain any flowlets. Because of this, the affinity between TCP flow and team member can change at any time as the dynamic balancing algorithm works to balance the workload of the team members.
Whether the team is configured with Switch Independent or one of the Switch Dependent modes, it is recommended that you use Dynamic distribution mode for best performance.
There is an exception to this rule when the NIC Team has just two team members, is configured in Switch Independent mode, and has Active/Standby mode enabled, with one NIC active and the other configured for Standby. With this NIC Team configuration, Address Hash distribution provides slightly better performance than Dynamic distribution.
Standby adapter setting
The options for Standby Adapter are None (all adapters Active) or your selection of a specific network adapter in the NIC Team that acts as a Standby adapter. When you configure a NIC as a Standby adapter, all other unselected team members are Active, and no network traffic is sent to or processed by the adapter until an Active NIC fails. After an Active NIC fails, the Standby NIC becomes active and processes network traffic. When all team members get restored to service, the standby team member returns to standby status.
If you have a two-NIC team and you choose to configure one NIC as a Standby adapter, you lose the bandwidth aggregation advantages that exist with two active NICs. You do not need to designate a Standby Adapter to achieve fault tolerance; fault tolerance is always present whenever there are at least two network adapters in a NIC Team.
Primary Team interface property
To access the Primary Team Interface dialog box, you must click the link that is highlighted in the illustration below. How to download synthesia.
After you click the highlighted link, the following New Team Interface dialog box opens.
If you are using VLANs, you can use this dialog box to specify a VLAN number.
Whether or not you are using VLANs, you can specify a tNIC name for the NIC Team.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |